Star Micronics Multi-Font NX-2415 Instrukcja Użytkownika Strona 28
- Strona / 134
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
ON LINE button
The ( ON LINE ) button sets the printer on-line and off-line. The state
changes each time you press the button.
In the on-line state the printer receives data from the computer and prints the
data. In the off-line state the printer stops printing and sends the computer
a signal indicating that it cannot accept data.
The printer powers up in the on-line state if paper is present. If paper is not
present, the printer powers up off-line with the POWER indicator flashing.
When you load paper the POWER indicator stops flashing, but the printer
remains off-line. To start printing you must press the ( ON LINE ) button
go on-line.
--
The three main times when you will want to press the(
ON LINE )button
are:
l Before and after any other panel operation
The other panel buttons operate only in the off-line state. First press the
( ON LINE ) button to go off-line, then perform the panel operation, then
press the( ON LINE )button again to go back on-line.
. To pause during printing
If you press the ( ON LINE ) button during printing, the printer stops
printing and goes off-line, allowing you to check the printout or change a
control panel setting. Printing resumes when you press the ( ON LINE >
button again to go back on-line.
. To cut fanfold forms at the end of printing
When using fanfold forms, if you hold the ( ON LINE )button down for
one second, in addition to go off-line the printer feeds the paper about two
inches forward, allowing you to cut it off just below the last line printed.
When you press the ( ON LINE )button again to go back on-line, the paper
feeds backward about one inch, stopping in the right place to resume
printing.
.-
- USERS MANUAL 1
- HOW TO USE THIS MANUAL 3
- Chapter 8 - Specilications 4
- FEATURES OF THE PRINTER 5
- TABLE OF CONTENTS 6
- Chapter 1 9
- UNPACKING AND INSPECTION 10
- Check the carton contents 10
- Parts name of the printer 11
- SElTlNG UP 12
- Mount the platen knob 12
- Connection 16
- LOADING SINGLE SHEETS 18
- Automatic loading 18
- Adjustable paper guide 19
- Manual loading 20
- Loading the fanfold forms 21
- POWER indicator flashing 22
- Paper parking 25
- Paper unparking 25
- Adjustment lever 26
- Chapter 2 27
- ON LINE button 28
- PAPER FEED button 29
- SET/EJECT PARK button 29
- PITCH button 29
- STYLE button 30
- Short test mode 31
- Long test mode 32
- Print area test mode 32
- Stay in panel pitch 32
- Stay in panel style 33
- Hexadecimal dump 33
- Form feed 36
- Top of form 37
- Forward micro-feed 37
- Reverse micro-feed 37
- Clearing the buffer 38
- Chapter 3 39
- PRINTER CONTROL COMMANDS 45
- Select L Q characters 46
- Select LQ font style 46
- Courier characters 47
- Select Optional characters 47
- Select Prestige characters 47
- Se/ect Orator characters 47
- Select Script characters 48
- Select italic characters 48
- Select upright characters 48
- Select ornament chatacter 48
- Emphasized printing 49
- Cancel emphasized printing 49
- Double-strike printing 49
- Start underlining 49
- CHARACTER SET COMMANDS 51
- Select IBM character set 51
- Select character set #I 51
- Select character set #2 52
- Elite pitch 54
- High-speed elite pitch 54
- High-density elite pitch 54
- Seim-condensed pitch 54
- Condensed printing 55
- Cancel condensed printing 55
- Expanded printing 55
- Cancel expanded printing 55
- Select character width 56
- Select proportional spacing 56
- Select fixed spacing 57
- Select master print mode 57
- Increase character spacing 57
- Select character size 58
- Return to normal height 59
- 27 73 n 1B 49 n 60
- VERTICAL POSITION COMMANDS 61
- I I I 62
- Feed paper n lines 64
- Set top margin 65
- Set bottom margin 65
- Set page length to n lines 65
- Disable paper-out detector 66
- Enable paper-out detector 66
- Set vertical tab stops 67
- Vertical tab 68
- Set left margin 68
- Set right margin 69
- Set left and right margins 69
- Carriage return 69
- Right justify 71
- Full justify 71
- Set horizontal tab stops 71
- Reset all tab stops 72
- Horizontal tab 72
- Relative horizontal tab 72
- GRAPHICS COMMANDS 73
- 27 09 nl n2 1B 59 nl n2 74
- 27 90 nl n2 74
- 1C 5A nl n2 74
- Select graphics mode 75
- Convert graphics density 76
- Define download characters 77
- Select ROM character set 78
- <CAN> 24 79
- Repeat data 80
- Quiet print 80
- Cancel quiet print 80
- Cancel immediate print 81
- Set printer off-line 81
- Set printer on-line 81
- Stop printing 81
- Bidirectional printing 82
- Unidirectional printing 82
- Manual feed 82
- Auto feed 83
- Eject paper from ASF 83
- Reset printer 83
- Chapter 5 85
- ASCII Code: 60 86
- Left space: 4 86
- Character width: 86
- Right space: 3 86
- Sample program 87
- 23. 0. 0 88
- DIFFUSION RANGES Of 89
- CARS & TELEPHONES 89
- Chapter 6 91
- EMBEDDING PRINTER COMMANDS 92
- COMMANDS 94
- PROGRAMMING WITH BASIC 96
- How the program works 102
- Quad-size 103
- Modifications for IBM mode 104
- Chapter 7 105
- Power supply 106
- Paper feeding 108
- ON LINE indicator 109
- MAINTENANCE 111
- REPLACING THE RIBBON 111
- REPLACING THE PRINT HEAD 112
- Chapter 8 115
- Chapter 9 119
- STANDARD CHARACTER 120
- 1 531 1 691 1 PSI I1011 120
- IBM CHARACTER SET #2 122
- 8 9 A 123
- B C D E F 123
- IBM CHARACTER SET #I 124
- IBM SPECIAL CH 125
- ARACTER SET 125
- #S@[\lA’C~>“@O 126
- COMMAND SUMMARY 130
Powiązane produkty i podręczniki dla Drukarki etykiet Star Micronics Multi-Font NX-2415
(128 strony)
(156 strony)
(100 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji